Computer Networks Questions & Answers – Virtual
Circuit
1. Which of the following is not a
characteristic of Virtual Circuit Network?
a) There are setup and teardown phases in addition to the data transfer phase
b) Resources can be allocated during setup phase or on demand
c) All packets follow the same path established during the connection
d) Virtual circuit network is implemented in application layer
a) There are setup and teardown phases in addition to the data transfer phase
b) Resources can be allocated during setup phase or on demand
c) All packets follow the same path established during the connection
d) Virtual circuit network is implemented in application layer
Answer: d
Explanation: Virtual circuit network is normally implemented in datalink layer.
Explanation: Virtual circuit network is normally implemented in datalink layer.
2. The address that is unique in the
scope of the network or internationally if the network is part of an
international network is called as
a) Global address
b) Network address
c) Physical address
d) IP address
a) Global address
b) Network address
c) Physical address
d) IP address
Answer: a
Explanation: This address is used to create a virtual circuit identifier.
Explanation: This address is used to create a virtual circuit identifier.
3. The Identifier that is used for
data transfer in virtual circuit network is
a) Global address
b) Virtual circuit identifier
c) Network identifier
d) IP identifier
a) Global address
b) Virtual circuit identifier
c) Network identifier
d) IP identifier
Answer: b
Explanation: Virtual circuit identifier is used for data transfer and has switch scope.
Explanation: Virtual circuit identifier is used for data transfer and has switch scope.
4. Which of the following is not a
phase of virtual circuit network?
a) Setup phase
b) Datatransfer phase
c) Termination phase
d) Teardown phase
a) Setup phase
b) Datatransfer phase
c) Termination phase
d) Teardown phase
Answer: c
Explanation: Virtual circuit network does not contain termination phase.
Explanation: Virtual circuit network does not contain termination phase.
5. Steps required in setup process
are
a) Setup request and acknowledgement
b) Setup request and setup response
c) Setup request and setup termination
d) Setup and termination steps
a) Setup request and acknowledgement
b) Setup request and setup response
c) Setup request and setup termination
d) Setup and termination steps
Answer: a
Explanation: Steps required in setup process are Setup request and acknowledgement.
Explanation: Steps required in setup process are Setup request and acknowledgement.
6. During teardown phase, source
after sending all the frames to destination sends……..to notify termination
a) Teardown response
b) Teardown request
c) Termination request
d) Termination response
a) Teardown response
b) Teardown request
c) Termination request
d) Termination response
Answer: b
Explanation: Source after sending all the frames to destination sends teardown request to which, destination sends teardown response.
Explanation: Source after sending all the frames to destination sends teardown request to which, destination sends teardown response.
7. Delay if, resource allocated
during setup phase during data transfer is
a) Constant
b) Increases for each packet
c) Same for each packet
d) Different for each packet
a) Constant
b) Increases for each packet
c) Same for each packet
d) Different for each packet
Answer: c
Explanation: If resource allocated during setup phase, delay is same for each packet.
Explanation: If resource allocated during setup phase, delay is same for each packet.
8. Delay if, resource allocated on
demand during data transfer is
a) Constant
b) Increases for each packet
c) Same for each packet
d) Different for each packet
a) Constant
b) Increases for each packet
c) Same for each packet
d) Different for each packet
Answer: d
Explanation: If resource allocated on demand, delay is different for each packet.
Explanation: If resource allocated on demand, delay is different for each packet.
9. In virtual circuit network, delay
times for setup and teardown respectively are
a) 1 and 1
b) 1 and 2
c) 2 and 1
d) 2 and 2
a) 1 and 1
b) 1 and 2
c) 2 and 1
d) 2 and 2
Answer: a
Explanation: Delay time for setup and teardown is one each.
Explanation: Delay time for setup and teardown is one each.
10. In data transfer phase, the
table contains how many columns?
a) 1
b) 2
c) 3
d) 4
a) 1
b) 2
c) 3
d) 4
Answer: d
Explanation: Table has 4 columns. Port and VCI for both incoming and outgoing data.
Explanation: Table has 4 columns. Port and VCI for both incoming and outgoing data.
تابع أسئلة الشبكات
ليست هناك تعليقات:
إرسال تعليق